定容下料器無加料命令時，擺動氣缸處在初始位置，此時下料口密封，其進料口敞開，處于進料狀態，當槽控箱發出加料命令時，擺動氣缸選擇90度，帶動芯軸和上下蓋板旋轉同樣的位置，這時上蓋板蓋住了進料口，解決了料箱中的料順勢流入，并只允許定容室中的物料順著下料口的打開而卸出。
不出料的定容下料器的維護:檢查料箱中是否有物料，如果沒有物料，通知給料車間添加物料；手動給料器應聽是否有流動的聲音，如果沒有聲音，就會卡住。應指示天車將進料器吊出進料器，以清理料倉和錐形塞。如果有聲音，表示氣缸與連桿連接處的銷軸斷裂，應指示天車將進料器吊出，更換銷軸；少下料定容下料器的維護:檢查氣源壓力，要求在0.4mpa以上；查看料倉中是否有足夠的物料，料倉中的料位要高于定容下料器料斗的料位。
氣缸運轉是否正常，潤滑是否良好；檢查定容下料器錐形塞與鋼瓶之間是否有雜物；感覺檢查材料的干燥程度是否符合要求。定容給料器泄漏的檢查和修理:檢查給料器油缸的活塞密封是否損壞和泄漏，損壞后更換；
根據活塞的壓力位置，確定定容下料器是否卡死，如停車時應將定容下料器提升到筒倉和錐塞進行清理；如果檢多，則證明定容下料器錐塞損壞應更換定容下料器。更換固定容積定容下料器：更換維修步驟：關閉替換定容下料器的供氣球閥，取消定容下料器的供氣管壓力；打開定容下料器的固定螺栓鉗，安裝卸料螺栓；使用吊索，命令起重機降落；安裝新的定容下料器。
; 雖然定容下料器的固定容量較為成熟，但日常維修或需要做好，以免影響生產。
